Biltwell RECOIL GRIPS - Oxblood
Regular price $29.95Construction: Injection-molded Krayton synthetic rubber
Fitment: Biltwell grips are available in 7/8" and 1". These grips are made from the same material used in dirt bike and BMX grips: Kraton Rubber. They are softer and more comfortable but also wear quicker. Just like a dirt bike, plan on changing them often, depending on how hard you ride and in what conditions.
Details: Scroll down for Installation Tips. We recommend using WD-40 to install the grips and suggest letting them dry overnight. Adding a ring of safety wire on each end is a standard moto practice and all of our grips have grooves to accommodate this.
Note: Using Biltwell rubber grips on H-Ds will often require that your motorcycle is equipped with an aftermarket throttle tube (our Whiskey throttle tube, for instance). The grips do not have a built-in plastic throttle tube, they are meant to slide over a higher-quality aluminum tube.
Biltwell Kung Fu Grips - Black
Regular price $29.95Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.
Technical Details
Install Tips
Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.
Biltwell Kung Fu Grips - Grey
Regular price $29.95Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.
Technical Details
Install Tips
Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.
Biltwell Kung Fu Grips - Chocolate
Regular price $29.95Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.
Technical Details
Install Tips
Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.
Biltwell Kung Fu Grips - Oxblood
Regular price $29.95Our Kung Fu grip's squishy surface design is cozy the second you grab it. New UV-resistant TPV synthetic rubber is soft, yet durable for miles of comfort.
Technical Details
Install Tips
Counterintuitive though it might seem, aerosol WD-40 spray lubricant is our chemical of choice for installing Biltwell moulded TPV grips. "But it's oil!" you say. Yes, but WD-40's combination of aerosol propellant and organic-based lubricant is perfect for sliding tight grips onto clean metal tubes. A quick 1- or 2-second blast into the open end of the grip is all it takes. Once installed, WD-40's chemical compound melts the grip interior just enough to make it stick to the bar like glue, without the mess. IMPORTANT: Wait 24 hours after installation before riding to give grips time to set up on the bars. Immediately after installation, you can add safety wire wraps to both ends of the grips; this old motocross trick works great to reduce grip slip on the bars and throttle tube.
TJ Brutal Malleus Machined Motorcycle Grips - Black
Regular price $139.95The Malleus Machined Grips for Honda Shadow are the perfect choice for your bobber or chopper build! The throttle sleeve tube fits most throttle cables and stock Honda shadow switch housings and the clutch side grip and throttle sleeve tube will work with all 1" handlebars.
The Malleus Machined Aluminum Throttle Sleeve and Clutch Grip set is the most simple way to set up your handlebars, no need for grips that will wear out or need replacing! The throttle sleeve and clutch side grip are machined from 6061 Aluminum and anodized with beautiful knurling, not too extreme, just enough to provide a solid hold! I always hated when grips were knurled to the point of aggressively shredding my palms!! Not so with the Malleus Grip Set! The throttle sleeve fits perfectly in our Acerus Throttle Assembly
The matching clutch side grip simply slides on and attaches to the handlebar with 3 included #6-32 set screws, we recommend using a bit of red loc-tite on each screw . Some folks like to add a dab of glue when sliding the clutch side grip on, but we have found it's not necessary.
The throttle sleeve is meant for single cable operation. It is not meant to run the push cable. You do not need the push cable, remove it and enjoy your newfound throttle performance!!
Fits 1" handlebars
Fits the following models throttle cables -
Honda Rebel
Honda Shadow VLX600 / VT600
Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS
Honda Sabre
Honda Magna
Honda VT1100
Honda VTX
*May fit other metric bikes.
While this part doesn't need grips, you can leave the clutch side grip off and use a traditional set of rubber grips. A rubber grip set will fit over the throttle sleeve.
We recommend using a tiny bit of red thread-locker on the set screws of the clutch side grip.
This is for the purchase of the grips only. The video is for example purposes and shows other pieces which are not included
TJ Brutal Customs THE BLACK BOX
Regular price $524.95THE BLACK BOX is a Complete Controls Kit that includes our Grips, Pegs, Shifter, Brake Peg, Throttle Assembly & Carb Shield
Experience the ultimate in black parts with the TJBC BLACK BOX. Whether you're looking for a fully murdered-out build or just want to add some darkness to your bike, this curated box has you covered. Indulge with the finest ALL BLACK parts.
Each Black Box Includes:
TJ Brutal Customs Tersus TSG - Motorcycle Throttle & Grip Kit for Honda Shadows
Regular price $319.95The Tersus TSG (Throttle and Steering Grip Kit) allows you to eliminate the unnecessary throttle push cable with our Acerus Single Cable Throttle Assembly, and upgrade your motorcycle grips to the "knurley" Malleus Grips all-in-one kit. This is an amazing Honda Shadow Bobber Kit!
INCLUDES
FITMENT
Fits 1" handlebars
Fits the following models throttle pull cables -
Honda Rebel
Honda Shadow VLX600 / VT600 / Steed
Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS
Honda Sabre
Honda Magna
Honda VT1100
Honda VTX
*May fit other metric bikes.
BENEFITS
The Malleus Machined Grips
These motorcycle grips are the perfect choice for your Honda Shadow bobber or chopper build! The throttle sleeve tube fits most throttle cables and stock Honda Shadow switch housings and the clutch side grip and throttle sleeve tube will work with all 1" handlebars.
The Tersus TSG - Motorcycle Throttle & Grip Kit for Honda Shadow is the most simple way to set up your handlebars, no need for motorcycle grips that will wear out or need replacing! The throttle sleeve and clutch side grip are machined from 6061 Aluminum and anodized with beautiful knurling, not too extreme, just enough to provide a solid hold! I always hated when grips were knurled to the point of aggressively shredding my palms!! Not so with the Malleus Grip Set! The throttle sleeve fits perfectly in the Acerus Single Cable Throttle Assembly.
The matching clutch side grip simply slides on and attaches to the handlebar with the included three, #6-32 set screws. We recommend using a bit of red loc-tite on each screw.
The throttle sleeve is meant for single-cable operation. It is not meant to run the push cable. You do not need the push cable, remove it and enjoy your newfound throttle performance!!
When installing the Malleus Motorcycle Grips, we recommend using a tiny bit of red thread-locker on the set screws of the clutch side grip.
The Acerus Single Cable Throttle Assembly
The Acerus single cable throttle assembly for the Honda Shadows is machined from billet aluminum, and made to work seamlessly with the stock Honda Shadow throttle pull cable. That's right! You do not need to run a push cable! The stock throttle assembly is quite bulky and lacks any kind of visual aesthetic. Who are we kidding, it's totally haggard!
Specs:
The Acerus allows you to maintain a clean, focused and custom look on your bars with no unnecessary fluff, but enough style to show you have superb taste. because you definitely do, you got-dang champion!
Fits the following models throttle cables -
Honda Rebel
Honda Shadow VLX600 / VT600
Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS
Honda Sabre
Honda Magna
Honda VT1100
Honda VTX
*May fit other metric bikes.
* Some models stock throttle sleeves may not fit.
Do not over tighten clamp bolts. Use red loctite on the bolts. Fits 1" bars, will accommodate most grips for 1 inch bars. When clamping the assembly on your bars, a small gap between upper and lower halves is normal, this ensures that the clamp isn't bottomed out before it can adequately clamp the bars. This allows the clamp to work well on raw material bars or bars that have plating or powder coating. When installing on powder coated bars, it may be necessary to use a mallet to tap the halves of the assembly together so the bolts can grab the threads. Powder coating isn't an exact science and the thickness can vary from brand to brand, there is no way to anticipate this and if we made the clamps ID bigger, it wouldn't fit chromed bars.
We advise using a bit of lubricant inside the throttle assembly and under the throttle sleeve for smooth twist action and prolonged life of the parts.
Kustom Tech Handlebar Grip Ring - Chrome
Regular price $67.95Handlebar grip ring fit all 1” handlebar, available in aluminum in polish or black anodized finish, and in brass in polish or chrome finish, the external diameter is 36mm.
Kustom Tech Handlebar Grip Ring - Black
Regular price $64.95Handlebar grip ring fit all 1” handlebar, available in aluminum in polish or black anodized finish, and in brass in polish or chrome finish, the external diameter is 36mm.